Q Series Stepper Driver

Contact

Description information

Q Series Stepper Driver

Contact

"Call 0974400989 for advice free call"

AME

100% new commitment
Genuine warranty

Mr. Hoàng Tấn
Hotline: 0974400989
Email: hoangtan@ame-engineering.com
Ms. Ánh Tuyết
Hotline: 0948998638
Email: anhtuyet@ame-engineering.com

Technical information

Q Series Stepper Driver Manual (2-phase & 3-phase)

Q series 2-phase & 3-phase stepper driver is the latest all-digital stepper driver. It uses servo control theory and the most optimized control calculation. It has no concepts of “beat” and “subdivision” of the traditional driver. No matter how many steps are set, the motor current is always the accurate sine current instead of current step. That is why the stepper motor h as the best performance, stability, and low-speed mute and extremely low heat productivity. The following are current waveform pictures of Q series driver and division driver tested under the same condition. Pictures are taken by the oscilloscope without any amendment.


Current waveform of Q series driver (800 steps)	Current waveform of subdivision driver (800 steps)

✔️ current waveform of Q series driver (800 steps)

✔️ accurate sine current control brings excellent performance

✔️ 255 options of steps for different transmission ratio

✔️ automatically record the breaking point when power off

✔️ set the rotation direction of the motor

✔️ input signal 3~24V, not need to externally connect current-limit resistor

✔️ perfect stability, low-speed mute, extremely low heat productivity

✔️ 16 kinds of lock time (0.1~2 seconds)

✔️set EN port to off-line mode or lock mode

✔️ current waveform of subdivision driver (800 steps)

✔️ single pulse, dual pulse

✔️ 11 kinds of lock current (0~100%)

✔️ 16 kinds of output current

✔️ easily set and read

✔️ auto run function

✔️ self-test ability

✔️ protection function

✔️work on drive technology for 30 years

1. List of 2-phase driver

Model

Input Power

Output Current

(16 kinds, peak)

Input

Signal

Alarm Output

Setting

Method

Dimension(mm) &

Installation

Motor

Picture

QU-2H302D

DC24V

0.8~3.0A

3~24V

programmer

92X55X17.5

Installation distance between two points 86.5

42BYG250A

42BYG250B

42BYG250C

57BYG250A

57BYG250B

QU-2H302D

QS-2H404D

DC24~40V

1.2~4.2A

3~24V

DIP switch

115X67X22

Installation distance between two points 108

57BYG250A

57BYG250B

57BYG250C

57BYG250D

57BYG250E

QS-2H403A

AC20~30V

3~24V

DIP switch

QS-2H403A

QX-2H504A

AC24~40V DC24~50V

1.5~5.0A

3~24V

DIP switch

120X73X26

Installation distance between two points 113

85BYG250A

85BYG250B

85BYG250C

QZ-2H606A	AC40~60V DC50~80V	2.2~6.0A	3~24V	Optocoupler Normally-closed output	DIP switch	132X86X53 Installation distance among four points 142X34	85BYG250A 85BYG250B 85BYG250C 85BYG250D
QG-2H808A	AC40~80V DC50~110V	2.5~8.0A	3~24V	Optocoupler Normally-closed output	DIP switch	132X86X53 Installation distance among four points 142X34	85BYG250A 85BYG250B 85BYG250C 85BYG250D
QD-2H611A	AC70~110V Rated AC110V	2.2~6.0A	3~24V	Optocoupler Normally-closed output	DIP switch	135X120X56 Installation distance among four points 143X34	110BYG250A 110BYG250B 110BYG250C 110BYG250D
QZtr-2H607A	AC40~70V DC50~90V	2.2~6.0A		Optocoupler Normally-closed output	Programmer Or CNC	192X120X56 Installation distance among four points 202X34	86BYG250A 86BYG250B 86BYG250C
QZtr-2H607A	The model is specially used for cutting machine and router. One QZtr-2H607A is the combination of 3 pieces of QZ-2H606A. Its parameters and performance are completely same as QZ-2H606A. It is small and it’s easy to install and connect wires. Its price is lower. It works perfectly with our CNC cutting controllers. It has no DIP switch. Parameters are set in the controller. The controller can control the driver.
Instrument	1. The current is peak value, peak value=effective valueX1.4 2. We offer the programmer to set drivers.